The Bargman Tail Light # 30-92-003 has 2 wires that receiver power and 1 wire designed to be grounded. You'll need to find the tail light circuit on your Jayco Eagle and attach it to the green wire; you'll attach the brake light/turn signal wire to the black wire and then the white wire to the ground wire.
You may need to use a circuit tester like the # PTW2993 to find which wires correspond to which function.
If there is a specific problem with the left side light, please let me know... view full answer...
The SnapPad Base for RV Plastic Leveling Blocks or Leveling Buckets # SN55FR would just snap onto the bottom portion of your Andersen Jack Block just as you would install SnapPads on your leveling jacks.
These SnapPads measure 14" x 14" x 1-1/4" and will fit most 12" leveling buckets like your Andersen Jack Blocks. view full answer...
Since your trailer wheels have 6 lug nuts each, I will make recommendations based on a “6 on 5-1/2” pattern since this is by far the most common. Be sure to verify your bolt pattern before ordering.
We have two 16” tire/wheel combos that have a 6 on 5-1/2 pattern and come with # ST235 85R/16 tires. The Kenda # AM35010 which comes with a plain black wheel and the Kenda # AM32734 which has a sporty aluminum wheel. Both are rated for load range E and Speed rated M for 81 MPH, and would be... view full answer...
The Ceiling Garnish for Ventline Roof Vent White # VA0445-37 has 5-5/16" legs and the Ceiling Garnish for Ventline Roof Vent Birch White # VA0445-29 has 5-1/8" legs. It sounds like you need the 5-5/16" legs, however, this is not available in birch white, just polar white.
Both parts have dimensions of 16" by 16". If your current vent garnish is also 16" by 16" then it sounds like the # VA0445-37 would work for you. view full answer...
The RR error code on your Lippert Ground Control # LC358590 is one of the errors listed in the manual, and it states to check harness connections at controller and at jack, check harness for damage and repair or replace as necessary. Normally to clear a code like this you have to extend the jacks 6 inches before retracting.
Since you still seem to be having an issue with the jack moving a small amount. I suggest pressing the retract button and the enter button simultaneously holding for... view full answer...
The operation for the Blue Ox SwayPro # BXW1000 is going to be the same even with using the larger 1,500lb Bars # BXW4008. With that said if this is a different trailer than the one you previously used the spring bars for the trailer itself may be different heights so you may need a different chain link to get the proper amount of spring tension on the bars. Personally I always recommend installing the hitch like it is a new trailer when changing parts on the hitch. This will allow you... view full answer...
Yes, you can. The Advent Air Replacement RV Air Conditioner for Coleman Setup w/ Start Capacitor item # ACCOL150B you were looking at is designed to replace Coleman setups like you have now. It will plug into the same connectors your RV has and use your current Coleman controls as well. Since this includes a start capacitor your 30 amp power source will work. view full answer...
Hey Vaughn, thanks for reaching out!
The max psi rating of the Americana Aluminum Mod Trailer Wheel # AM22646 will be the equivalent to the rating of the valve stem that you install on it. The Americana Metal, Bolt-In Valve Stem # AM20906 can handle up to 200 psi so I recommend installing this on the wheel. view full answer...
The best option to replace the hubs on your 1995 Jayco 1207 tent trailer are the Dexter Trailer Idler Hub Assembly item # 8-91-05UC1-EZ. This hub has a 4 on 4 bolt pattern and is designed for 2,000 lbs axles with item # L44649 inner and outer bearings. This hub is sold individually and includes all necessary bearings and seals to install on your trailer. Also included are four replacement lug nuts.
A BTR spindle has a grease zerk at the end. This can be easily accessed with the removable... view full answer...
Per Lippert, the correct replacement for a PowerGear 524235 slide out motor would be the Replacement PowerGear RV Above Floor Slide-Out Motor - Double Shaft - Mid Torque # LC368417. view full answer...
If you replace your PD4045CS with the part # PD4045CSV you'd have ability to switch between lead acid and lithium battery types like you are wanting to. I attached a link to a page that has wiring diagrams for you to check out as well. This comes with instructions too. view full answer...
The correct braking assembly for your 2000 Jayco Eagle UDST Pop-Up Camper is most likely the Hydraulic Trailer Brake Kit part # AKUBRK-35 which is 10" x 2-1/4" but if you take a quick measurement of the contact surface inside your drum you should be able to confirm this.
The correct hub/drum assembly for your 2000 Jayco Eagle UDST Pop-Up Camper will be a bit more difficult to find because there are a few different options depending on axle capacity. In order to confirm this I would need... view full answer...
Do understand the Trailer Wheel Center Cap # 482EZ you found is sized too fit a wheel with an opening of 4.82" and the center is smaller allowing it to fit inside the wheel. Our next smallest size center cap is the Americana # AM90077 which is designed to fit a wheel with a 4.25 or 4.27" pilot hole. Be sure to check your wheels pilot hole size to determine the correct fit. view full answer...
Since you have Dexter axles that have a 6 lug bolt pattern then the Westlake ST225/75R15 Radial Tire w 15" Liger Aluminum Wheel # LH36FR is going to fit and work well. If your tire size is 225/75R15 then this would work great as a spare.
Sounds like you have jacketed lug nuts which are known to swell over time and eventually can break like what you described. We have solid lug nuts like the part # KALN1375S which is solid stainless steel and fits the common trailer wheel stud size of 1/2 inch. view full answer...
Since we know your 2021 Jayco Eagle 330 RSTS has two 6k axles we can help you convert it to a disc brake setup. For the hub/rotors you'd wan the Kodiak Disc Brake Kit part # K2HR526D (6 on 5-1/2") for each axle and then for the rest of the disc brake components you'd want the Hydrastar Electric Over Hydraulic Actuator Kit for Disc Brakes # HBA16-252-82 which comes with all of the other components you'd need like brake lines and breakaway kit but also comes with the best and most reliable... view full answer...
Hydraulic brakes are typically better than electric brakes. They engage quicker and more evenly but we're talking fractions of a second. The hydraulic brakes having a 1/2" more braking surface will help them stop quicker.
To replace your 7" drums, I recommend the Dexter Trailer Hub and Drum Assembly item # 8-173-16UC3. These are for 2,200 lbs axles and work with both drum and electric brakes. They have a 4 on 4 lug pattern and include lug nuts, bearings, races, and seals. This hub fits... view full answer...
We have the exact Solera slide toppers your your 84-3/4", 144-1/2", and 156-1/4" flange to flange measurements, and they do come in black as well. The exact parts you need are the following:
- 84-3/4": Solera RV Slide-Out Awning - Black # LCV000165062
- 144-1/2": Solera RV Slide-Out Awning - Black # LCV000177334
- 156-1/4": Solera RV Slide-Out Awning - Black # LCV000168109 view full answer...
I attempted to look up the provided model number that you gave but I was not able to find anything, however I won't leave you empty handed.
What I can say, without any other knowledge of your setup is, if you had let's say a Coleman air conditioner on your 2008 Jayco Eagle, then you could use the Advent Air Replacement RV Air Conditioner for Coleman Setup # ACCOL150 as a replacement.
This AC will utilize your existing Coleman equipment by way of the included wiring harness, will work... view full answer...
It sounds like you're looking for the LaSalle Bristol Double RV Waste Valves - Sanitation Tee # 34466ND15AAR.
This tee has a 3" hub that'll slide over your main 3" black waste spigot, and also includes a 1-1/2" that will go to your grey water line. view full answer...